Drawers & Hardware · Lubbock & West Texas

Furniture Hardware Repair in Lubbock, Texas

Drawer, Slide, Hinge and Mechanism Repair for Dressers, Desks and Cabinets at Our Wolfforth Workshop

Does a drawer stick, fall out or hang crooked? Is a pull loose or a hinge bent? Bring it to our Wolfforth shop, about 12 miles from Lubbock. Call 806-414-1519 or request an estimate online. Send photos first, and we will tell you what is possible.

What Is Furniture Hardware Repair?

Furniture hardware repair is the fixing of the parts that open, close and hold a piece of furniture. That means drawers, slides, hinges, pulls, knobs and locks. We repair the part and the wood around it, because a worn part often damages the wood it sits in.

PartCommon faultUsual fix
Drawer boxLoose corners, split frontClean, re-glue and clamp
Drawer bottomSagging or splitRe-seat or cut a new bottom
Wood runnerWorn groove, no stopRebuild the runner, add a stop
Metal slide or glideBent, dirty, worn rollerStraighten, re-mount or replace
HingeLoose, stripped screw holesPlug, re-drill and reset
Pull or knobLoose or cracked postRe-seat or repair the post

Who Does Furniture Hardware Repair in Lubbock?

Reimagined Antiques does furniture hardware repair in Lubbock at our workshop in Wolfforth, about 12 miles southwest of the city. From Texas Tech or downtown, take the Marsha Sharp Freeway (US 62/82). The drive takes about 16 minutes.

If you searched for furniture hardware repair Lubbock, this is the shop. We are a repair workshop, not a furniture store. We fix the drawers and hardware on the pieces you already own.

What Does Dresser Drawer Repair Include?

Our dresser drawer repair covers the drawer box, the bottom, the runners and the hardware. For other single faults, see our furniture repair page.

Broken Drawer Repair

Broken drawer repair usually means a split front, a loose corner or a cracked side. We clean the old glue from the joint, glue it fresh and clamp it square. We keep original dovetail joints where we can. If the front has veneer, see our veneer repair page.

Sagging and Split Drawer Bottoms

A drawer bottom slips out of its groove or splits under weight. We re-seat it, or cut a new bottom and fit it into the groove. A sound bottom keeps the drawer square.

Drawer Track Repair for Wood Runners

Many older pieces ride on wood runners instead of metal slides. Over the years the runner wears down, and the drawer drops, rubs or tips out. Drawer track repair means building up or replacing the worn runner and adding a stop block, so the drawer cannot fall out when you pull it.

Repair Drawer Slides and Repair Drawer Glides

We repair drawer slides and repair drawer glides by cleaning them, straightening bent parts, tightening loose screws and lining the drawer up again. If the rollers are worn out, we replace the slide.

Desk Drawer Repair

Desk drawers carry heavy loads such as files and books, so the bottom, the sides and the slides take a beating. Desk drawer repair at our shop covers all three. For fold-down and roll-top desks, see our roll-top desk repair page.

Furniture Drawer Repair for Nightstands, Buffets and Cabinets

Furniture drawer repair covers nightstands, buffets, sideboards, vanities and china cabinets.

How Does Drawer Slide Repair Work?

Drawer slide repair starts with the type of slide. Each type fails in its own way.

Slide typeWhere you find itUsual faultOur fix
Wood runnerOlder and antique piecesWorn groove, no stopRebuild the runner, add a stop
Side-mount ball-bearingDesks and cabinetsBent, dirty, loose screwsClean, straighten, re-mount
Roller glideDressers and nightstandsWorn or cracked wheelReplace the glide
Center-mount glideDressers and vanitiesCracked track or bent guideRepair or replace

If a slide is bent past saving, we replace it. We keep the original wood runner whenever it can be saved.

Why Does a Drawer Stick, Fall Out or Hang Crooked?

Wood takes in and gives off moisture, and it changes size as it does. The U.S. Forest Service Forest Products Laboratory explains this in its Wood Handbook. Lubbock gets about 18 inches of rain a year, and the air is dry. Wood shrinks in dry months and swells after wet spells. A drawer that fit last winter can bind in a damp spring.

SignLikely causeUsual fix
Drawer sticksSwollen wood, dirt, worn runnerClean, level and wax the runner
Drawer falls outNo stop block, worn runnerAdd a stop, rebuild the runner
Drawer hangs crookedLoose joints, worn rollerRe-glue, replace the roller
Drawer rubs one sideBent slide, loose screwsStraighten, re-mount
Bottom sagsSplit bottom, loose grooveReplace the bottom

What About Hinges, Pulls, Knobs and Locks?

Hinges loosen when the screw holes strip out. We fill the hole with a wood plug, drill it again and reset the hinge, so the door hangs and closes square. Pulls and knobs loosen when the post or the hole wears. We re-seat them and repair cracked posts.

Matching old hardware is hard. We try to match a missing pull to the rest of the set. If no match exists, we tell you your options, such as a full new set. We adjust stiff locks and drop-front parts where we can. For made-to-order parts, see our custom woodworking page.

Can I Fix a Drawer Myself, or Should I Hire a Pro?

You can wax a sticky runner, tighten a loose screw and wipe dirt out of a track. Leave glue joints, slide replacement and stripped screw holes to a shop.

Is It Better to Repair or Replace Drawer Hardware?

Repair the part when the part is the only fault. On an antique, keep the original hardware when you can, because swapping it can lower the value. We do not appraise furniture. If you think a piece is rare, ask an appraiser before anyone changes the hardware. For older pieces, see our antique furniture restoration page.

What Does Drawer Repair Cost in Lubbock?

We do not post a flat price, because every drawer is different. For furniture hardware repair in Lubbock, we send a time-and-materials estimate after we see your photos, before work starts.

FactorWhy it changes the estimate
Number of drawersMore drawers mean more hours
Type of faultA loose pull takes less time than a rebuilt runner
Slide typeWood runners take more hand work than a new glide
Missing hardwareA part that is hard to match adds time

How Does Furniture Hardware Repair Work Step by Step?

  1. Request an estimate. Our online form asks for your name, details about the fault, and photos.
  2. Get your estimate. We review your details and send a time-and-materials estimate.
  3. Accept it. Work follows a first-in, first-out line, set by deposit date and an accepted estimate.
  4. Bring it in. We do not pick up furniture, so you drop off the piece at our shop.
  5. Repair it. We fix the wood first, then the slides and hardware, then touch up the finish. For color and sheen, see our furniture refinishing page.
  6. Pick up. We contact you when the piece is ready at our Wolfforth workshop.

Furniture Hardware Repair Near Me: Lubbock, Wolfforth and the South Plains

Our shop is in Wolfforth on the Marsha Sharp Freeway (US 62/82). Dowden Road (FM 179) is the main north-south road. We serve Lubbock and the rest of West Texas.

If you search for furniture hardware repair near me, you want a shop close enough to visit. We are a drop-off workshop. We do not pick up furniture, and we do not make house calls. For tabletops and leaves, see our table repair page.

How Can You Tell a Repair Shop Will Do Good Work?

Look for a shop that asks for photos, gives a written estimate and explains each fix. Ask whether the original hardware can stay. A good shop also tells you when a part should be replaced. That is how we run furniture hardware repair in Lubbock.

Customers on our Google profile describe our team as courteous and on time, and praise a china cabinet that was repaired, given new hardware and refinished.

Furniture Hardware Repair in Lubbock FAQs

It depends on the number of drawers, the fault, the slide type and the wood. We do not post a flat price. We send a time-and-materials estimate before work starts.

Often, yes. We clean, straighten and re-mount slides that are bent or dirty. If the rollers are worn out, we replace the slide.

Older drawers on wood runners often have no stop block, and the runners wear down. We rebuild the runner and add a stop, so the drawer stops before it leaves the frame.

Clean the runner and rub on a little wax. If the wood is swollen or the runner is worn, bring the piece in, and we will level and repair it.

We try. If no match exists, we tell you your options, such as repairing the part or replacing the whole set. On an antique, we suggest keeping the original when it can be saved.

No. We are a drop-off workshop and we do not pick up furniture. You bring the piece to our Wolfforth shop and pick it up when it is ready.

For furniture hardware repair in Lubbock, it depends on the job and our queue. Work follows a first-in, first-out line. We give you timing in the estimate.

Send photos of the whole piece, close-ups of the drawer or hardware, and the size. Tell us what the fault is and what you want done.

Related Services

Ready to Fix Your Drawers?

Call 806-414-1519 or request an estimate online. Then bring your piece to our Wolfforth workshop.

13405 Upland Ave 1600, Suite 28, Wolfforth, TX 79382